Skip to content

Where is the camshaft sensor on a 2008 nissan sentra?

Where are camshaft sensors located?

The Camshaft Position sensor is typically located in the cylinder head of the engine and has a cylindrical portion that inserts into the head. The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block.

Where is the crankshaft sensor located on a 2008 Nissan Sentra?

Crankshaft Position (CKP) sensor is on the rear of the cylinder block.

Where is the camshaft position sensor located on a 2008 Nissan Altima?

Nissan Nissan Altima 2007-09 CMP Sensor Repair Guide

  1. The Camshaft Position (CMP) sensor is located on top of the engine at the flywheel end-2.5L engine.
  2. The Camshaft Position (CMP) sensors are located on top of each rocker cover at the flywheel end (front cylinder bank shown)-3.5L engine.

What are the symptoms of a camshaft sensor?

Symptoms Of A Bad Camshaft Position Sensor

  • Check engine light.
  • Stalled engine.
  • Unable to start the car.
  • Rough idle.
  • Reduced engine power.
  • Bad gas mileage.

Do you have to replace both camshaft sensors?

Do you have to replace both camshaft sensors? Experts recommend replacing both camshafts at the same time. The replacement process of the camshaft and the crankshaft is the same. But, you may face difficulty while detecting the location of the crankshaft.

What happens if you unplug camshaft position sensor?

What Happens If I Unplug A Camshaft Position Sensor? The answer is yes. Neither the cam shaft (or crankshaft sensor) nor computer will begin operating if it doesn’t receive a signal from them, so we don’t want to damage or disable it. A broken cam bolt or gear will probably be the cause of the lack of signal.

What causes P0335 code?

What the P335 code means. The P0335 DTC is set once the powertrain control module (PCM) fails to detect proper sensor operation from the crankshaft position sensor. This causes the Check Engine Light to be displayed on the dashboard and a failsafe mode enabled.

Where is the camshaft sensor on a 2011 Nissan Sentra?

What the P335 code means. The P0335 DTC is set once the powertrain control module (PCM) fails to detect proper sensor operation from the crankshaft position sensor. This causes the Check Engine Light to be displayed on the dashboard and a failsafe mode enabled.

How do you test a crankshaft position sensor?

Connect your meter leads to the sensor pins. Make sure to keep your meter lead wires away from engine moving parts during this test. Have an assistant crank the engine for a few seconds while you watch the meter’s readout. The sensor should produce a voltage pulsing signal.

Where is the bank 1 camshaft position sensor?

Beneath the timing belt cover is where the CMP Sensor is mounted. The camshaft position sensor can be found in the right side of the engine compartment at the rear of the valve cover.

What does a camshaft sensor do?

The camshaft sensor enables the engine control to determine the exact position of the crankshaft drive. This information is required to calculate the ignition point and injection point, among other things.

What does code P052B mean?

OBD-II Code Decreased engine performance is defined as a Cold Start “A” Camshaft Position Timing Over-Retarded. The engine control module (PCM) monitors Ignition Timing on initial startup. If the Ignition Timing varies excessively from where it should be, the PCM will set code P052B.

How do I know if my camshaft position sensor is bad?

A glowing check engine light, stalling, poor acceleration and bad fuel mileage are all possible signs your camshaft position sensor may be failing. Gone are the days of carburetors and distributors, replaced by a variety of sensors that help a car’s computer get the maximum performance out of the engine.

Will a bad camshaft sensor throw a code?

Answer: Usually a camshaft sensor intermittent failure can produce no code. But you’ll notice a change in driveability performance at times. Sometimes it’s possible to detect the failure with a scan tool.

Will a car start without a camshaft sensor?

The car doesn’t run. The engine will either start or stall if it doesn’t turn over. The engine will run poorly if the same sensor is unplugged and no signal is sent.

How much does a camshaft sensor cost?

The sensor will cost somewhere between $50 and $100 depending on the manufacturer. Installation can vary depending upon the car, and will run from $40 to $200 depending upon the location. Sometimes other parts of the engine need to be removed in order to access the sensor, and this may include the valve cover.

Should camshaft sensor have oil on it?

It’s a normal thing for a camshaft position sensor to have oil on it. The oil is necessary for its functionality. However, the sensor housing has to be in good shape to work perfectly. A crack in the sensor housing can result in oil contamination which could make the sensor fail.

How many camshaft sensors are in a car?

While the number can vary based on the age of your car, a new car should have four camshaft sensors, one for each camshaft. A camshaft sensor determines the exact position of your engine’s camshaft, helping your car keep your engine’s combustion running smoothly.

What sensor will keep a car from starting?

A crankshaft position sensor (crank sensor) is an important device measuring the engine RPM and tracing the crankshaft position. The car won’t start if the crankshaft position sensor doesn’t work properly. The crank sensor can fail, or its wiring can get damaged. This may cause the car to stall or not start.

Are camshaft sensor and crankshaft sensor the same?

The main difference between the camshaft and crankshaft position sensors is that the camshaft position sensor is used to find the position of the camshaft while the crankshaft position sensor is used to detect the position of the crankshaft and piston.

Does camshaft position sensor affect oil pressure?

If the oil level is very low, to the point where the engine overheats however, yes. Excessive heat can cause a camshaft position sensor to fail. More likely in a “low oil level” situation is for the camshaft, lifters, or camshaft variable timing actuator to fail due to inadequate oil pressure and lubrication.

Can you drive with P0335 code?

Other Notes About P0335

You shouldn’t continue to drive your vehicle once it triggers this code. An issue with the CKP can cause your vehicle to stall—and that can be dangerous. Get your car diagnosed immediately if you run into this trouble code (or the related trouble codes P0336, P0337, P0338, etc.).

Where is crankshaft sensor located?

The sensor is at either the front or the back of the crankshaft, so it’s usually located either on the transmission bellhousing or behind the crankshaft pulley. There should be a small air gap, usually about a millimeter or two, between the sensor and the reluctor.

Can P0335 cause misfire?

Potential Symptoms of P0335

Although, if your vehicle uses the crank sensor to check for misfires and spark timing, then it is possible that your car might not start. Therefore, the typical symptoms of a P0335 code are a misfire, MIL illumination, or failure to start.