Skip to content

When should a timing belt be replaced on a jeep wrangler?

Although timing belts are critical, there’s no need to replace them regularly –unless explicitly recommended in your Jeep owner’s manual. Some automakers recommend changing a timing belt between 60,000 and 100,000, others don’t. Many of today’s timing belts can go 100,000 miles or more without needing to be replaced.

How much does it cost to replace a timing belt on Jeep Wrangler?

Belts themselves aren’t that expensive. The real cost is in the labor, because a lot of parts need to be disassembled to get to the belt. Shopping around to get a few quotes is your best bet to get the best deal, but you can expect to pay anywhere from $409 to $919 (including parts and labor).

Do Jeep Wranglers have a timing belt?

The 2012 Jeep Wrangler comes equipped with a timing chain instead of a timing belt. It is better when a chain is used because it typically doesn’t need to be replaced unlike the timing belt. The chain is located inside of the engine so it is not exposed like the belt which is outside of the engine and is exposed.

How much does it cost to replace a timing chain on a Jeep?

The Best in Auto Repair

The average cost for a Jeep Wrangler timing chain and gear set replacement is between $746 and $856. Labor costs are estimated between $422 and $533 while parts are priced at $324. This range does not include taxes and fees, and does not factor in your specific model year or unique location.

What are the signs that you need a new timing belt?

5 Common Signs Your Timing Belt Needs to Be Replaced

  • Engine Makes a Ticking Noise. When the timing belt starts to wear out, it may create a ticking sound inside the motor. …
  • Engine Won’t Turn Over. …
  • Engine Misfires. …
  • Rough Idling of the Engine. …
  • Decline in Oil Pressure and Oil Leaking.

How much does it cost to fix timing chain?

Timing chain replacement can cost between $413 and $1,040. The cost is high due to the complicated nature of replacing this part. If you want to DIY a timing chain replacement, the parts will cost $88 to $245.

Does a 2005 Jeep Wrangler have a timing belt or chain?

They have timing gears no chain no belt.

Does the 3.6 Pentastar have a timing belt?

The 3.6L Pentastar makes use of a timing chain in place of a timing belt. The timing drive uses four chains, each of which is a “silent chain link” design to improve sprocket engagement and cut noise, vibration, and harshness (NVH). These chains need to be replaced at some point.

At what mileage should a timing chain be replaced?

Unless there is a specific fault, the timing chain should be replaced between 80,000 and 120,000 miles. Chain problems are frequent in automobiles with increasing mileage. If you’re driving an older car or one with a lot of miles on it, keep an eye out for signs that the timing chain is failing.

Is it worth fixing a timing chain?

A timing chain doesn’t need to be replaced unless there is a problem with it. Is the timing chain immune to mechanical failures? The simple answer is No, it is not. Timing chain problems are not uncommon, especially in high-mileage vehicles.

What are the symptoms of a failing timing chain?

Signs of a Faulty Timing Chain

  • Rattling Sound on Starting the Engine or Idling. A common finding in a vehicle with a bad timing chain is unusual rattling noise when the engine is started or when brakes are engaged. …
  • Misfiring Engine. …
  • Contaminated Engine Oil. …
  • Check Engine Light. …
  • Inability to Start the Engine.

Does timing belt give warning?

The timing belt can fail without any prior symptoms, so if you’re within the mileage window, you should go ahead and have it replaced regardless. That being said, sometimes your car will give you a bit of warning that the belt is wearing out.

How much should a new timing belt cost?

If your timing belt is in need of replacement, you can expect that service to cost anywhere from $300 up to $500. Because the timing belt is not easily reachable on many vehicles there is a good bit of disassembly and reassembly needed to get to the belt. Economy cars with smaller engines require less labor.

How long does it take to change timing belt?

Due to the intricacy involved in getting such an operation done, a typical timing belt replacement will usually take between 4 and 6 hours to complete. This might change depending on your car and your mechanic, but it’s a safe bet to expect the job to take quite a while.

How many hours does it take to replace a timing chain?

Overall, replacing the timing chain and its associated hardware should take a qualified mechanic 5 to 8 hours to complete.

Will a broken timing chain destroy my engine?

A broken timing chain will cause an engine to not start or fail while driving. If the belt is already broken, the engine won’t have enough compression to start. If it breaks or jumps while driving, the pistons will be damaged from contact with the valves. The valves themselves will bend and potentially ruin the engine.

What’s better timing chain or belt?

Most automakers recommend replacing the timing belt every 60,000 to 105,000 miles. Timing chains are heavier and more complex than timing belts, but they also last much longer. Really, unless there’s a problem, timing chains don’t have a replacement interval.

Is the Jeep 3.6 a good engine?

The 3.6 L FCA Pentastar V6 Engine is an overwhelmingly durable and reliable engine. That’s why it’s been used in in more than ten million Chrysler, Dodge, and Jeep vehicles since 2010. With proper maintenance the 3.6L Pentastar engine can provide years of reliable service.

How long does the Jeep 3.6 engine last?

With proper maintenance the 3.6L will EASILY achieve 200 – 300,000 miles with no major repairs.

When should I replace my timing chain 3.6 Pentastar?

These chains need to be replaced at some point. I would say a safe time to do this is around 90 000 miles – 120 000 miles. Signs of a worn-out chain include loud rattling noises which means its probably time to start thinking of replacing the chains.

Can a timing chain last forever?

A: As a general rule, if an engine has a timing chain and the oil was changed on a regular basis, the timing chain should last the lifetime of the engine.

Do Timing chains last longer than belts?

In summary: Timing chains last longer than timing belts, but they are a bit more expensive. There are no performance gains or fuel efficiency gains if you use one over the other. Cheaper cost was the main reason for the use of timing belts in cars.

How do you check timing chain?

To accurately identify the amount of wear in a timing chain, begin by removing all of the spark plugs and the distributor cap. With a wrench on the harmonic balancer bolt, turn the crankshaft at least two complete revolutions backward of rotation to remove any slack from the timing chain.