Notes: AutoGrade – (Carded), M14 x 1.50 Thread size. SAE/Metric 21 Head size.
What size is oil drain plug on Jeep Wrangler?
Dorman – Help – Oil Drain Plug Pilot Point M14-1.50, Head Size 16mm (Part No. 69010)
What size socket is my oil drain plug?
Place a 3/8-inch (0.9 centimeters) socket in the socket wrench, fit it over the drain plug’s nut and turn it counterclockwise. The oil drain plug should open easily, draining the used oil from the engine. Make sure to place a bucket and some newspaper under the car’s engine to catch all the draining oil.
What size is the oil drain plug bolt?
Oil Drain Plug Standard M14-1.50, Head Size 17mm.
What size bolt is on a Jeep Wrangler oil pan?
If you have a 2.4L, the screws are M6 x 1.0 x 17.
How much oil does a 2010 Jeep Wrangler take?
Capacity: With filter 6 quartsAfter refill check oil level.
How many quarts of oil does a Jeep Wrangler JK take?
Engine Oil
With filter 5.9 quartsAfter refill check oil level.
How do I know what size drain plug I have?
Measure Diameter
Measure the width of the plug at the widest part of the threads. If your plug measures 12mm you will need to start looking at plugs in the size range of “M12 x 1.25 to M12 x 1.75″. The “M12” refers to the diameter you measure from the widest part of the threads on your OEM sump plug.
What is the socket size?
Metric Socket Sizes Chart
| 3/8″ Drive | 1/4″ Drive | 1/2″ Drive |
|---|---|---|
| 7mm | 5mm | 10mm |
| 8mm | 5.5mm | 11mm |
| 9mm | 6mm | 12mm |
| 10mm | 7mm | 13mm |
Are drain plugs universal?
This plug is universal. It should fir on any oil pan. The only thing about it is that it is intended to be permanent. In other words, you don’t want to unscrew it too often to replace the oil.
What size is the drain plug on a 2010 f150?
The oil drain plug size on a 2010 ford f150 is 21mm.
Are oil drain plugs reverse threaded?
it is regular-threaded. Righty tighty. Also, as the plug is threaded into aluminum, I like to use a torque wrench on mine so as not to over tighten. Proper torque for the drain plug is 18 lb/ft.
How do you remove an oil drain plug?
You’ll need to spray penetrating oil on the oil plug and leave it to sit for several hours. Then you can take a small hammer and tap counterclockwise to ensure that you are loosening the plug.
What type of oil does a 2012 Jeep Wrangler take?
For JK Wranglers from 2012-2018 with the Pentastar 3.6L engine, Mopar recommends using six quarts of 5W-20 oil, however you can also use 5W-30 depending on what type of driving conditions you expect to encounter.
What size is the oil drain plug on a Jeep Cherokee?
Dorman – Help – Oil Drain Plug Pilot Point M14-1.50, Head Size 16mm (Part No. 69010)
What kind of oil does a 2013 Jeep Wrangler take?
Gather the Needed Supplies. Per Owner’s Manual the 3.6L Pentastar engine in the 2013 JK takes 6 quarts of 5W-20 motor oil. Experience put the fill at just a little under this (about 5.6 quarts).
What size is the oil drain plug on a 2011 Jeep Wrangler?
Notes: AutoGrade – (Carded), M14 x 1.50 Thread size. SAE/Metric 21 Head size.
Can you use 5W-30 instead of 5W-20?
Can You Use 5w30 Instead Of 5w20. It is not recommended. Although they both have the same winter rating of 5, the thickness (viscosity) of 5w30 is a bit higher than 5w20. That means your engine’s at stake for using the high viscosity oil.
What kind of oil goes in a 2010 Jeep Wrangler?
Notes: Full synthetic high mileage. 5W-20. 5 quarts container.
How much oil does a 3.8 L Jeep Wrangler take?
6 quarts. (with filter)After refill check oil level.
Can I use 5W-30 instead of 5w20 in my Jeep Wrangler?
In cold temps 5w20 and 5w30 should have the same viscosity. The difference would be as the oil is warmed up, like in a running engine. The 5w30 should be a little thicker, so it should (as you mentioned) have a slightly higher oil pressure at operating temp.
How many quarts does a jeep 3.6 take?
Capacity: With filter 5.9 quartsAfter refill check oil level.
What size is oil drain plug 5.3 Vortec?
The oil drain plug on a chevy silverado is 15mm.
What is an oil drain plug gasket?
The drain plug gasket seals the drain plug located at the bottom of the oil pan, which holds your vehicle’s engine oil. If you have oil leaking from the bottom of the oil pan, it may be the fault of a leaky drain plug or gasket.
What is the standard size of a bath plug?
Standard bath plugs measure about 1-3/4 inch (44.5mm) diameter and suit the hole in a 1-1/2 inch BSP waste.