Skip to content

How much is an ignition switch for a 2002 jeep liberty?

How much does it cost to replace the ignition switch on a Jeep Liberty?

The replacement cost includes both spare parts and ignition switch repair labor costs. The labor costs can be anywhere between $60-$180, and the parts can cost around $70-$300.

How much does it cost to replace ignition switch?

The average cost for ignition switch replacement is between $176 and $214. Labor costs are estimated between $77 and $98 while parts are priced between $98 and $117. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

What problems do 2002 Jeep Libertys have?

Top 2002 Jeep Liberty Problems

  • Check Engine Light/Misfire Due to Intake Valve Locks/Valves. …
  • Power Window Motor May Fail Due to Regulator Assembly. …
  • The Sky Slider Sunroof May Not Open. …
  • Engine Will not Start Due to Wireless Control Module Fault. …
  • Front/Rear Differential Pinion Seal/Transfer Case Leaks are Common.

What does an ignition switch do?

The ignition switch is party of an assembly, or system, that includes the ignition lock cylinder. The entire mechanism is responsible for starting your car as well as providing power to specific areas of the vehicle, such as the electronic accessories, the ignition, and the engine.

How much does it cost to replace a Jeep ignition?

Jeep Wrangler Ignition Switch Replacement Cost Estimate. The average cost for a Jeep Wrangler ignition switch replacement is between $124 and $139. Labor costs are estimated between $51 and $65 while parts are priced between $73 and $74.

How much does it cost to replace a ignition switch on a 2006 Jeep Liberty?

Jeep Liberty Ignition Switch Replacement Cost Estimate. The average cost for a Jeep Liberty ignition switch replacement is between $107 and $119. Labor costs are estimated between $44 and $56 while parts are priced at $63.

Do you need a new key when replacing ignition switch?

To replace an ignition switch, you’ll need to either have your old switch rebuilt by a dealership so you can keep your old keys or purchase a new switch from a dealership and get a new set of keys.

Can you replace an ignition switch yourself?

Proper testing should always be done prior to replacing the ignition switch. If you have further issues, or if you are not comfortable replacing the switch yourself, a certified mechanic from YourMechanic can replace your ignition switch for you.

How do I know if I have a bad ignition switch?

Signs Of A Faulty Ignition Switch

  1. Car Won’t Start. If you turn your key and the car attempts to start, but fails, then you might have a broken ignition switch. …
  2. Key Won’t Turn. …
  3. Car Stalls. …
  4. No Noise From The Starter. …
  5. Dashboard Lights Flicker.

How many miles can you get out of a Jeep Liberty?

In short, jeep liberty’s are reliable and can last 10-15 years on average. However, it largely depends on how well the car is maintained, in terms of mileage they can last 200000-400000 miles before any major issues occur.

Do Jeep Liberty have a lot of problems?

While some years are unreliable, you’ll be pleased to find that most of these vehicles will run for a long time without too many issues. In fact, the Jeep Liberty ranked 5th out of 10 Jeep models for reliability. Still, the Jeep Liberty is notorious for having problems.

Why did jeep discontinue the Liberty?

Jeep discontinued the Liberty CRD for the American market because it could not meet tougher 2007 emissions standards for diesel engines. Transmission choices were both carry-overs: a six-speed manual or a four-speed automatic.

What happens when ignition switch goes bad?

A bad ignition switch won’t be able to supply power to the starter motor, ignition system, and other engine controls, preventing the engine from starting. Keep in mind, however, that engine issues may also be caused by other electrical and mechanical problems, such as a dead battery or a faulty starter solenoid.

How do I know if my ignition switch fuse is bad?

Usually a bad or failing ignition relay will produce a few symptoms that can notify the driver of a potential issue.

  1. Car suddenly stalls while operating. One of the most common symptoms of a failed ignition relay is a car that suddenly stalls while operating. …
  2. Car not starting. …
  3. Dead battery. …
  4. Burned relay.

What causes ignition switch failure?

Worn ignition switch contacts, temperature problems, or broken springs can all cause the ignition switch to fail, preventing you from starting your car. On the road, poor ignition switch contacts could shut the engine off while driving, which could be dangerous.

How long does it take to replace ignition switch?

Usually, an ignition switch replacement will only take about 20 minutes. However, it could take much longer depending on your car’s make and model and the complexity of the ignition covers.

How much does it cost to fix a key ignition?

Replacement ignition costs may vary depending on what type of vehicle you have. The average cost is anywhere from $150-500 for parts and labor, but this will differ depending on how extensive repairs are needed.

Does ignition switch need to be programmed?

Ignition switches can now be programmed to electronic ignition keys to add extra security and safety to your vehicle. These keys are synced with your engine to start your car, and once you program them, only a programmed key will start your car.

How do you test an ignition switch?

Put the ignition key into the ignition switch and crank the engine. If the engine cranks, then your ignition switch is obviously working fine. If the engine does not crank, and you hear a “click” when you first turn the key to the “III” position, then your ignition switch is not the problem.

Can a car ignition be rekeyed?

Yes, there are only two methods that can be used rekey a car. The first is used by a few locksmiths, but it is not a great option. This method removes a few of the wafers that are inside of the lock, and will re-arrange some of the other wafers, to make the new key work in the ignition.

What’s the ignition on a car?

The purpose of the ignition system is to generate a very high volt age from the car’s 12 volt battery , and to send this to each sparkplug in turn, igniting the fuel-air mixture in the engine ‘s combustion chambers .