Skip to content

How much is a clutch for a 2008 jeep wrangler?

We currently carry 3 Clutch Set products to choose from for your 2008 Jeep Wrangler, and our inventory prices range from as little as $241.99 up to $539.99.

How much is it to replace a clutch in a Jeep Wrangler?

The average cost for a Jeep Wrangler clutch replacement is between $1,537 and $1,663. Labor costs are estimated between $471 and $594 while parts are priced between $1,066 and $1,069. This range does not include taxes and fees, and does not factor in your specific model year or unique location.

How long does it take to replace a clutch in a Jeep Wrangler?

The clutch will typically last up to about 100,000 miles depending on driving habits. The clutch replacement requires auto repair experience and will take at least 15 hours.

How many miles will a 2008 Jeep Wrangler last?

The Jeep Wrangler boasts extreme longevity

A Wrangler can typically reach 280,000 miles before significant problems begin to surface. But well-maintained models exceed 20 years and over 400,000 miles. The Wrangler is built for the outdoors and designed to tackle tough terrain, contributing to its longevity.

How do I know if my clutch is bad in my Jeep?

Symptoms and Causes of a Bad Clutch

  1. Symptom: Engine’s Moving Quickly, Car’s Moving Slowly. …
  2. Symptom: Car is Noisy in Neutral, but Quiets Down When Clutch Pedal is Pressed. …
  3. Symptom: Squealing or Chirping When Clutch Pedal is Pressed. …
  4. Symptom: Horrible Grinding Noise. …
  5. Symptom: Car Can’t Get Into Gear.

How long does Jeep clutch last?

Under normal conditions the clutch should run you over 100k easy.

How long should a clutch last Jeep TJ?

If you know what you’re doing, a clutch should last well beyond 100K miles…..

How long do Jeep manual transmissions last?

Registered. If your asking on the life of a manual trans I would say at least 200-500K miles. It all depends on how the previous drivers abused it.

How do you change a clutch on a Jeep TJ?

Registered. If your asking on the life of a manual trans I would say at least 200-500K miles. It all depends on how the previous drivers abused it.

At what mileage do Jeeps start having problems?

Jeeps typically start having problems around 100,000 miles. According to one Jeep forum, at 100,000 miles, you can expect to need to service the engine, transmission, differentials, and bearings.

How many miles is too much for a used Jeep Wrangler?

Jeep Wranglers can easily surpass 100,000 miles. Even older Jeep Wranglers in decent condition can last beyond 200,000. Newer models that are taken care of and are in excellent condition can go up to 3400,000. They are a great investment, even with high mileage.

Are there any recalls on 2008 Jeep Wrangler?

Recall no. CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2008 JEEP WRANGLER MANUFACTURE BETWEEN JUNE 2006 THROUGH JULY 2008 PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSION. THESE VEHICLES WERE NOT EQUIPPED WITH A TRANSMISSION FLUID TEMPERATURE WARNING SYSTEM.

How much does a clutch cost?

The Best in Auto Repair

The average cost for clutch replacement is between $1,222 and $1,398. Labor costs are estimated between $585 and $738 while parts are priced between $637 and $660. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

How do I know when my clutch needs replacing?

5 signs that your clutch needs to be changed

  1. Difficulty shifting gear.
  2. Squeaking or grumbling noise when the clutch pedal is pressed.
  3. Spongy, sticking, vibrating or loose clutch pedal when pressed.
  4. Ability to rev the engine, but poor acceleration.
  5. Slipping’ clutch, causing a momentary loss of acceleration.

How can I tell if my clutch is going out?

You are most likely to notice this when putting the car in reverse and first gear.

  • Slipping. This is exactly what it sounds like. …
  • Burning smell. A burning smell many times goes hand-in-hand with a failing clutch. …
  • Noises. …
  • Sticky or stuck pedal.

Can you replace clutch yourself?

If you are sure that your clutch has worn out beyond repair then you can potentially replace the clutch yourself at home. It is possible, but it is a relatively lengthy and complicated procedure. There are several fiddly steps where there is a wide scope for things to go wrong.

How much time does it take to replace a clutch?

Clutch replacement can take as little as 2-3 hours, but on average the total job time sits at around 5 hours. The first part of the process is the removal of the old clutch.

How long will a clutch last after it starts slipping?

When you continue driving with a slipping clutch, it can cause severe damages to your gearbox and the clutch, which will deeply cost you during repairs. You may need to replace the clutch at around 30,000 miles, even though other clutches can continue slipping up to 100,000 miles.

How much does it cost to replace a manual transmission in a Jeep Wrangler?

The cost of your Jeep transmission repair or rebuild will depend on which parts need to be replaced and how many service hours the project will require. However, the average transmission replacement cost starts at about $1,800 and can cost as much as $3,400.

What year did Jeep have transmission problems?

The most common Jeep Cherokee transmission problems occur in the 2014 and 2015 models. Problems include: Shifting roughly or not shifting properly.

What problems do Jeep Wranglers have?

One of the most common complaints about the 2019 and 2020 Wranglers is insufficient power and torque, loose driving wheels, and they’re too expensive for what you get. There are also reports of a faulty fuel tank that could cause the vehicle to stall.

How does a Jeep Wrangler clutch work?

Because fluid is not compressible, the force of you moving the clutch pedal down is transferred to the slave cylinder, where the fluid then extends a rod. This rod pushes on the clutch fork, which slides the throwout bearing (clutch release bearing) away from the carrier and into contact with the pressure plate.

How do clutches work?

A clutch works with two rotating shafts — one that is typically driven by a motor or pulley and one that drives another device. The clutch connects the two shafts so they can either be locked together and spin at the same speed, or be decoupled and spin at different speeds.

How do you change a clutch on a Jeep Wrangler JK?

A clutch works with two rotating shafts — one that is typically driven by a motor or pulley and one that drives another device. The clutch connects the two shafts so they can either be locked together and spin at the same speed, or be decoupled and spin at different speeds.