Skip to content

How much does it cost to replace ball joints on a jeep wrangler?

How much does it cost to replace ball joints on a Jeep?

The Best in Auto Repair

The average cost for a Jeep Grand Cherokee suspension ball joint replacement is between $195 and $245. Labor costs are estimated between $88 and $111 while parts are priced between $107 and $134.

How long do Jeep Wrangler ball joints last?

Stock JK OEM ball joint life expectancy varies widely. Some have gone out in 20,000 miles, some have lasted over 100,000 miles.

How long does it take to replace ball joints on a Jeep?

The work will take about 1 hour to complete. However, additional time may be necessary depending on how dealer appointments are scheduled and processed.

How much should it cost to replace ball joint?

Average Ball Joint Replacement Cost

You might be surprised to learn that replacing a ball joint is not overly expensive. You can expect to pay around $300 in most cases, including both parts and labor. Most ball joints cost about $100 to $150, while the labor costs will run you $150 to $200.

How long does it take to replace ball joints?

It can take a little over an hour to get it replaced, so the full ball joint replacement cost will be between $100 and $400.

How many ball joints does a jeep have?

Usually, most auto vehicle and Jeep models consist of four-ball joints in front of their suspension, which mainly ensures the connection between the wheels and the suspension system. Although ball joints are not prone to fail or wear out very easily, you should replace them whenever they turn bad.

How do you know if your ball joints are bad on a Jeep JK?

Steering wander, death wobble, poor road tracking, or suspension popping can all be signs of worn ball joints. However, these symptoms might also be due to other worn steering components or loose wheel bearings. To check a set of ball joints at one front tire, it’s best to jack the tire off the ground.

How often replace ball joints on Jeep Wrangler?

Ball joints are one of those common factory wear items that will need to be replaced on your Jeep, with the typical service interval of tens of thousands of miles when running the stock suspension and tires.

What do ball joints do on a Jeep?

Ball joints act as a pivot, allowing the vehicle’s wheels and the suspension system to move in tandem. They connect the steering knuckles to the control arms and allow for smooth, dependable control of the suspension system when the steering wheel is turned.

How much is a ball joint for a Jeep Liberty?

The average cost for a Jeep Liberty suspension ball joint replacement is between $574 and $603. Labor costs are estimated between $111 and $140 while parts are priced at $463.

How do you change a ball joint on a Jeep?

The average cost for a Jeep Liberty suspension ball joint replacement is between $574 and $603. Labor costs are estimated between $111 and $140 while parts are priced at $463.

How do I change a JK ball joint?

The average cost for a Jeep Liberty suspension ball joint replacement is between $574 and $603. Labor costs are estimated between $111 and $140 while parts are priced at $463.

Do you need an alignment after replacing ball joints?

There’s no denying that it’s very important to replace your ball joints when needed. However, it’s worth noting that doing that doesn’t necessarily mean you need an alignment. The only time you need one after replacing the ball joints is if the previous alignment was performed when ball joints were not in good shape.

Should you replace all ball joints at once?

If a customer needs a new ball joint, recommend replacing all of the joints at the same time. If one joint has failed, chances are the other joints may be nearing the end of their service life, too.

Should I replace upper and lower ball joints at the same time?

A: Plenty of mechanics will recommend that you replace both the upper and lower ball joints at the same time. They may also recommend checking related components at the same time, such as the stud hole in the steering knuckle.

How do you replace upper and lower ball joints?

A: Plenty of mechanics will recommend that you replace both the upper and lower ball joints at the same time. They may also recommend checking related components at the same time, such as the stud hole in the steering knuckle.

How long does it take to replace ball joints and tie rods?

The inner and outer tie rods on your vehicle can take up to some time. The dealership will change out the tie rod ends and then perform a vehicle alignment, so the time there will be to the upper 3 to 4 hours.

What is a suspension ball joint?

Ball joints consist of a ball and socket similar to the hip joint of the human body. Ball joints of your front suspension provide pivoting movement between the steering knuckles and control arms to provide a safe, smooth ride and allow you to precisely control your vehicle.

What is the difference between upper and lower ball joints?

The lower ball joint is the load-carrying joint in this type of suspension, while the upper ball joint is the follower, with no significant load to support. It acts only as a second pivot point for steering. Most modern ball joints are sealed and do not require lubrication as they are lubed for life.

How do you check ball joints on a Jeep Cherokee?

Checking your ball joints when driving is straightforward, simply:

  1. Take your car out for a drive. …
  2. Drive over speed bumps. …
  3. Turn the steering wheel. …
  4. Check your tyre wear. …
  5. Loosen the lug nuts. …
  6. Jack up the car and place wheel chocks behind the wheels. …
  7. Rock the tyre on its axis. …
  8. Remove the wheel.

How long can you drive on bad ball joints?

short answer is… it depends on how bad they are. the lower ball joint typically gets more wear than the upper. i’d say, if there’s just a little wiggle in either joint, you should have no problem driving 500 miles.

Can bad ball joints cause death wobble?

Worn ball joints and unit bearings are also a significant cause of death wobble.

How do I know if my lower ball joints are bad?

Worn ball joints and unit bearings are also a significant cause of death wobble.

Do Jeep Wranglers have rear ball joints?

The rear doesn’t have ball joints, only the front so you can turn. The ball joints are a pivot point for the front knuckles to turn left and right.

How do you press a ball joint on a Jeep Wrangler?

The rear doesn’t have ball joints, only the front so you can turn. The ball joints are a pivot point for the front knuckles to turn left and right.