Skip to content

How much does a starter cost for a 2002 jeep liberty?

We currently carry 6 Starter products to choose from for your 2002 Jeep Liberty, and our inventory prices range from as little as $129.99 up to $178.99.

How much does it cost to replace a starter on a 2002 Jeep Liberty?

Jeep Liberty Starter Replacement Cost Estimate. The average cost for a Jeep Liberty starter replacement is between $310 and $417. Labor costs are estimated between $88 and $111 while parts are priced between $222 and $306.

How much is a starter for a Jeep 2002?

2002 Jeep Wrangler Starter – from $109.99+ | AutoZone.com.

Where is the starter on a 2002 Jeep Liberty?

2002 Jeep Wrangler Starter – from $109.99+ | AutoZone.com.

How much should I pay for a starter replacement?

A brand new starter could cost you around $50 – $350, while labor costs from a qualified mechanic could range between $150 – $1,100. In total, replacing a bad starter motor could amount to between $200 – $1450. However, these figures could be lower if you’re able to identify car starter issues early.

How much is a starter for Jeep?

The average cost for a Jeep Wrangler starter replacement is between $293 and $392. Labor costs are estimated between $83 and $105 while parts are priced between $209 and $287.

How much does it cost to fix a starter on a Jeep?

A starter replacement typically costs between $440 and $551. Labor costs can be between $112 and $141, while the parts cost between $307 and $410. Of course, this is exclusive of tax and fees.

Where is the starter on a 2002 Jeep Cherokee?

A starter replacement typically costs between $440 and $551. Labor costs can be between $112 and $141, while the parts cost between $307 and $410. Of course, this is exclusive of tax and fees.

How do you test a starter to see if it’s good?

The starter should spin/crank the engine. If it does, the problem is with the cables, connections or relay. If it doesn’t, crank the engine, connect the black/negative jumper cable as a ground between the drivetrain and negative terminal of the battery. Touch the red cable to the starter’s positive terminal.

Why is my Jeep Liberty not starting?

The most common reasons a Jeep Liberty won’t start are a dead battery, an alternator problem, or failed starter.

How do you start a Jeep Liberty starter?

The most common reasons a Jeep Liberty won’t start are a dead battery, an alternator problem, or failed starter.

How do I know if my starter is bad?

Still, look for these seven symptoms that your starter is going bad.

  1. #1: Engine Won’t Turn Over. …
  2. #2: Noise – Clicking, Grinding, or Whirring. …
  3. #3: Intermittent Issues Starting the Vehicle. …
  4. #4: Starter Stays On After Starting. …
  5. #5: Smoke. …
  6. #6: Starter Engages But Motor Won’t Start. …
  7. #7: Battery.

How long does it take to fix a starter?

How long does it take to replace a starter motor? Depending on the type of vehicle, typically a starter motor replacement will take a mechanic between 2 and 4 hours to complete from start to finish.

Can AutoZone check starter?

Every AutoZone in the USA will check your alternator, starter, or battery at no charge.

How long should a jeep starter last?

On average, a starter motor lasts for 100,000-150,000 miles.

What happens when a starter goes out on a car?

When the starter drive gear is worn out or not engaging properly, it will often produce a grinding noise. This is similar to the one that is heard if you start your engine and then accidentally action the ignition switch again. If the grinding symptom is ignored, it may also result in damage to the engine flywheel.

Where is Jeep Wrangler starter located?

Your starter can usually be found on the driver’s side of the motor, just below the left bank of cylinders.

Can I replace a starter myself?

You can buy a new starter, which is rather expensive, or you can buy a rebuilt starter, which is just as good as a new one [source: Allen]. If the problem is really your starter, save yourself a trip to the mechanic and replace it yourself.

How do you tell if it’s your starter or ignition switch?

Test the Starter

It is under the hood, usually on the passenger side at the bottom of the motor next to the transmission. The ignition switch is a set of electrical contacts that activates the starter and usually is located on the steering column.

How much is a starter?

A new starter may cost between $80 and $350, but you should also factor in labor costs which may cost between $150 to $1,000. For most vehicles, the complete starter replacement cost is around $500.

How do you fix a starter?

A new starter may cost between $80 and $350, but you should also factor in labor costs which may cost between $150 to $1,000. For most vehicles, the complete starter replacement cost is around $500.

How much is a starter for a Jeep Cherokee?

The average cost for a Jeep Cherokee starter replacement is between $387 and $419. Labor costs are estimated between $99 and $124 while parts are priced between $289 and $294.

Where is the starter motor on a Jeep Cherokee?

The average cost for a Jeep Cherokee starter replacement is between $387 and $419. Labor costs are estimated between $99 and $124 while parts are priced between $289 and $294.

When your car won’t start but all the lights come on?

If your headlights can turn on, but your car won’t crank, that means that your battery is charged, but either the starter or ignition is the problem. If the starter or ignition is the problem, a starter engine can be jumped by using a charged battery.

What should be done before beginning a starter replacement?

How to Replace a Starter

  1. Safety First. Disconnect the battery. …
  2. Remove the Wiring. Remove the wiring and positive battery cable from the starter solenoid.
  3. Remove the Starter and Bolts. Remove the starter retaining bolts. …
  4. Compare to Verify. …
  5. Transfer Heat Shield. …
  6. Replace with New Starter. …
  7. Secure and Tighten. …
  8. Connect the Wiring.

How do I know if my starter has power?

To check the voltage reaching the starter, connect the voltmeter to the starter feed terminal and earth it on the starter casing. Test the voltage reaching the starter. For a negative-earth system on a car with a pre-engaged starter, connect the positive lead of the voltmeter to the feed terminal on the solenoid.