Skip to content

How do you reset the throttle position sensor on a jeep?

Step 1: Turn the Jeep to the “on” position but not the engine running position. Step 2: Wait for all of the dummy lights to turn off (check engine light will stay on). Step 3: Depress the accelerator REALLY slowly… Driving Miss Daisy with a touch of Cocoon slowly…all the way to the floor.

How do I reset my electronic throttle control on my jeep?

Resetting Your Electronic Throttle Control

  1. Step 1 – Make sure the accelerator pedal is fully released. …
  2. Step 2 – Turn the ignition on and then turn it off. …
  3. Step 3 – Turn the ignition on again for 7 seconds and then press the gas pedal five times before releasing for 5 seconds.

How do I reset my throttle position sensor?

The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.

Do you have to reset computer after replacing throttle position sensor?

Do You Have To Reset Computer After Replacing Throttle Position Sensor? Once the throttle body has been replaced, your engine will eliminate the pending code by detecting any engine light on and the issue going away. The ECM (computer) might reset itself if a hard permanent code was used in it.

How do you test a throttle position sensor on a Jeep?

Take the butterfly shaft and manually turn it. As you turn it, you should get a gradual count on the meter upwards to five volts. If the volts fluctuate backwards or forwards erratically, then you know you have a faulty TPS.

How do you reprogram a throttle body?

Turn the ignition switch on and wait 3 seconds. Immediately after the 3 seconds, the accelerator pedal must be pressed and released 5 times within 5 seconds. Wait 7 seconds and fully press the accelerator pedal and hold for approximately 20 seconds until the check engine light stops blinking and stays on.

What happens if you disconnect throttle position sensor?

What Happens If You Disconnect Throttle Position Sensor? TPS, as we call it, is the most important sensor in a car that is used to ensure gas and temperature doesn’t reach zero. Without it, the system cannot predict what’s happening with gas and temperature.

How do I fix code P0123?

What repairs can fix the P0123 code?

  1. Repairing or replacing the TPS connector for shorting.
  2. Repairing the wiring short as necessary.
  3. Replacing the TPS with a new sensor.

How do you reset the throttle body sensor on a Jeep Patriot?

What repairs can fix the P0123 code?

  1. Repairing or replacing the TPS connector for shorting.
  2. Repairing the wiring short as necessary.
  3. Replacing the TPS with a new sensor.

Does a throttle body sensor have to be programmed?

Yes, a new throttle body needs reprogramming so that it adapts to its new vehicle. Some vehicles automatically reprogram the throttle body when their installation ends. First, the mechanic must install the throttle body. Then turn on the engine for several minutes to idle.

How do you test a throttle position sensor?

Testing it involves grounding the connectors’ terminals as you put the multimeter probe on black to negative and red to positive. Make sure the throttle is fully closed by turning the key without starting the vehicle. Then read the voltage. The TPS voltage should be between .

Does a throttle position sensor need to be calibrated?

Once you have fitted a Throttle Position Sensor, or TPS, you will need to calibrate it from within MEITE. First, be sure you have correctly wired, and assigned the throttle sensor signal input to “TPS Raw” in the Analog Settings.

Can you drive without a TPS sensor?

The TPS or Throttle Postition Sensor tells the ECU how far the throttle is open, thus how much fuel is demanded. You will still be able to drive without a TPS, though not very well. The ECU will see a lean condition from the o2 once to open the throttle and it will atempt to richen it up.

What is code P1121?

OBDII code P1121 is Throttle Position Sensor Circuit Intermittent High Voltage. If you have changed it recently it could be out of adjustment or faulty.

What can cause a TPS code?

The voltage of the throttle position sensor can drop below the expected range for several reasons, including the following:

  • A loosely-mounted throttle position sensor.
  • Electrical short on the sensor circuit, either to the ground or to another wire.
  • Faulty sensor.
  • Faulty throttle position switch.

How do you reset the ECU on a Jeep Patriot?

Jeep ECU Reset Procedure

  1. Disconnect the battery by removing the positive battery cable. …
  2. Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
  3. Reconnect the positive cable to the battery.
  4. Turn the key to on but do not start.
  5. Turn the headlights on.

How do I reset my Jeep computer?

Registered

  1. disconnect positive battery cable.
  2. disconnect negative batter cable.
  3. hold both cables together for 30 seconds.
  4. connect positive back up.
  5. connect negative.