Skip to content

Where is the egr valve located on a ford expedition?

How do you clean the EGR valve on a Ford Expedition?

The start-stop system detects when the car is stationary and on the basis of sensors it determines a series of other factors about the operating mode of the vehicle. If the driver has stopped at a traffic light and sets the transmission to neutral, the start-stop system stops the engine.

Where is the EGR valve normally located?

Answer: The purpose of the EGR valve is to recirculating engine exhaust gas to the back to the engine cylinders. To accomplish this task the EGR valve is attached to the intake manifold of the engine. This location is atop of the engine near the carburetor, usually towards the back of the engine near the firewall.

Where is the EGR valve located on a 2000 Ford Expedition?

The EGR valve is located in the engine compartment (underneath the hood).

Car 2000 Ford ExpeditionV8-4.6L
Service Service typeExhaust Gas Recirculation/EGR Valve Replacement
Estimate Estimate$307.95
Shop/Dealer Price Shop/Dealer Price$371.19 – $538.40

Where is the EGR valve on a Ford?

The EGR valve sits on the top of the engine near the rear of the block and looks like a round disk with a small vacuum tube attached to the top center of the disk. A steel tube runs from the base of the valve to the exhaust manifold that threads into the side of the EGR valve.

How do you clean an EGR valve without removing it?

How To Clean an EGR Valve Without Removing It

  1. Gather the needed cleaning supplies.
  2. Locate the EGR Valve.
  3. Gain access to the EGR Valve.
  4. Start the vehicle and rev it to 2000 RPMs.
  5. Spray half of the cleaning solution (250ml)
  6. Reinstall the EGR valve cover.
  7. Scan the vehicle for error codes.

How much does it cost to clean the EGR system?

The cost of parts will be somewhere around $190 to $270, while the cost of labor will be anywhere from $60 to $80.

What are the symptoms of a faulty EGR valve?

What are the symptoms of a failing EGR valve?

  • Your engine has a rough idle. …
  • Your car has poor performance. …
  • You have increased fuel consumption. …
  • Your car frequently stalls when idling. …
  • You can smell fuel. …
  • Your engine management light stays on. …
  • Your car produces more emissions. …
  • You hear knocking noises coming from the engine.

Can I replace my EGR valve myself?

In most models, replacing an exhaust gas recirculation (EGR) valve is not difficult. You can do it in your garage in about an hour or two, depending on your particular system, using some common tools and a good solvent like carburetor cleaner.

What causes EGR valve failure?

The failures are usually caused by a build-up of deposits in the EGR valve over a period of time that causes them to stick. This build-up is part of the ordinary operation of the vehicle and should be regarded as a serviceable item requiring repair or replacement.

How do you clean an EGR valve?

To clean the valve, wear an acid-resistant pair of gloves. Put on safety glasses, too, as the carbon deposits could become airborne in the process. Spray the EGR valve cleaner onto the carbon deposits. Remove the carbon buildup with the use of a pipe cleaning brush and dull scraper.

Whats a EGR valve do?

It connects the exhaust manifold to the intake manifold and is controlled by either a vacuum or a built-in electric step motor. The function of the EGR valve is to control the flow of exhaust gas being recirculated depending on the engine load.

Where is the EGR valve on a 2010 Ford Explorer?

Raise the hood and locate the EGR valve, which is attached to the right rear on the intake manifold near the firewall. The intake manifold is attached to the side of the engine block.

Will fuel injector cleaner help EGR valve?

In order to be able to clean properly, 2 products are needed, a product that cleans the fuel system, Tecflow Speed Cleaner and Tecflow Top Engine Cleaner that cleans the fuel system by the air inlet. This optimally cleans the EGR system, the EGR valves, the intake manifold and the inlet valves.

How much does it cost to replace the EGR valve?

The average cost for EGR valve replacement is between $332 and $413. Labor costs are estimated between $81 and $103 while parts are priced between $251 and $311. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

Does cleaning EGR valve work?

Cleaning your EGR valve will solve your car’s engine performance issues related to any clogging or system passages problem with the valve. Even more importantly, it’ll prevent serious engine damage and expensive repairs.

Is it worth replacing EGR valve?

On older cars operated by engine vacuum, the EGR valve diaphragm can deteriorate and leak, causing a rough idle and a check engine light. In that case, the valve should be replaced. Also, over time the valve can accumulate carbon buildup and stick open, causing a rough running engine.

Does carbon clean clean EGR valve?

A commonly asked question is, does carbon cleaning clean the egr valve. Good news yes it does.

Can the EGR valve cause starting problems?

The exhaust gas recirculation (EGR) valve introduces a measured amount of exhaust gases, into the intake manifold to get re-burned. This helps lower engine temperature and harmful emissions. But, the valve can fail and stick either open or closed. When the valve sticks open it may prevent your engine from starting.

What happens if the EGR valve is stuck open?

If the EGR valve is stuck in the open position, the vehicle will experience a rough idle or frequently stall. If the valve is not completely stuck open but never achieves a tight seal when it closes, the engine can “miss” or shudder because of the improper mixture of the combustion elements.

Can I drive with a faulty EGR valve?

Can I drive with a bad EGR valve? Technically, you can drive your vehicle with a bad EGR valve, but your vehicle will run rough, shake at idle, and a check engine light will be illuminated. You might also hear popping sounds while driving down the road.

What will a stuck closed EGR valve do?

Can I drive with a bad EGR valve? Technically, you can drive your vehicle with a bad EGR valve, but your vehicle will run rough, shake at idle, and a check engine light will be illuminated. You might also hear popping sounds while driving down the road.

How do you tell if your EGR valve needs to be cleaned or replaced?

How to Tell If Your EGR Valve Is Bad. Once you have removed your EGR valve, shake it lightly. If you hear something moving back and forth inside, that’s the diaphragm—which means there is a good chance that your EGR valve is still good and just needs to be cleaned to return to normal function.

How do you reset a EGR valve?

RE: EGR VALVE RESET ? to reset the CEL just unhook your NEG from the battery for about 10 mins or more and it resets when power is hooked back up…. if there is still a problem the CEL will come back on after some time.

How long does it take to change a EGR valve?

Usually the replacement of the EGR valve is completed after 1 hour. For some older models, half an hour is sometimes sufficient. For tighter built models, the replacement can take 2-3 hours.