Skip to content

What does check brake system mean on a 2010 ford fusion?

The most likely issue is that your brakes need service (fluid filled, brake pads replaced, etc.), but it may also mean that there’s a malfunction somewhere in the system. If the message does not clear, or comes back again, have your car inspected as soon as possible.

What does it mean if it says check brake system?

It means that the car’s computer has detected a problem with the Brake system and needs to be inspected, if you see one that reads “CHECK BRAKE SYSTEM”. Is this true? If the message doesn’t clear, you should have your car inspected as soon as possible.

Is it safe to drive with brake system light on?

Driving with the Brake Warning Light on should not be done as this is dangerous. It means your brakes are not working properly and need to be repaired as soon as possible.

What causes brake system malfunction?

The most common cause of failure is a leak in the brake lines. The brake fluid will slowly drain out, until there isn’t enough left to transmit the pressure from the pedal to the tires. The brakes can also fail when the discs or drums wear out, so they can no longer put enough friction on the wheels to stop them.

What should you do if the brake system warning light comes on?

Drive the car to a parking area or onto the shoulder of the road as safely as possible and gradually press the brake pedal to bring your vehicle to a stop. Once safely stopped and out of the traffic flow, make arrangements to transport the vehicle to your favorite repair shop.

What 2 reasons would cause your brake system warning light to come on?

Here are the most common reasons why your brake warning light is on:

  • An Engaged Parking Brake. This is the most common reason why your brake light is on. …
  • Low Brake Fluid Levels. …
  • Worn Out Brake Pads. …
  • Anti Lock Braking System Malfunction. …
  • Defective Sensors. …
  • Faulty Rear Brake Light Bulb.

How do you check brake system?

Checking how your brake system is working starts with your brake pedal. Next, your brake fluid should be checked. Along with checking the brake fluid, the hoses and lines should be checked. Finally, the brake assemblies are checked.

The Brake Pedal

  1. Brake pedal height.
  2. Free play.
  3. Brake pedal reserve distance.

What does it mean when your brake light and ABS light comes on?

If both the ABS and the brake system light come on at the same time, your vehicle is no longer safe to drive. This means there is a serious problem with the car’s braking system and continuing to drive puts yourself and others at risk.

Why is my red brake light on?

A red light that flashes on and off could signal low/almost empty brake fluid, but also a serious issue with the brake’s hydraulic system. If the light comes on and stays on, you could end up with a potentially catastrophic (and costly) brake failure.

Are you at fault if your brakes fail?

In most cases where brakes fail, the car may rear-end a vehicle ahead, often at a high rate of speed. However, if you have taken all reasonable measures and necessary steps to ensure that your brakes are working properly, and they unexpectedly fail, the fault is with the brakes, not your negligence.

What are signs of brake problems?

8 Signs You Could Have Brake Problems

  • Brake Light On. …
  • Squealing or Squeaking Noises. …
  • Grinding Noises. …
  • Wobbling or Vibration When Braking. …
  • Leaking Fluid. …
  • Spongy or Soft Brakes. …
  • Car Pulling to One Side When Braking. …
  • Burning Smells.

Can brakes suddenly fail?

Yes. It is possible for the brake system to stop working suddenly, but sudden and total failure is rare, especially if you take a few simple precautions. Sudden brake failure is not only terrifying, but it is also one of the most dangerous mechanical failures that can happen while you are driving a car.

Can you reset brake warning light?

Service the brakes according to the problem diagnosed by the code. Attach the OBD scanner back to the port and turn the key in the ignition again without starting the engine. Press “OK” to read the code then press “Delete” to clear the Brake Warning light.

Can bad brake pads cause ABS light to come on?

To Be Clear, Worn Brakes CAN Cause The ABS Light To Come On, But It’s Not Why You Think. Your brakes and your ABS are not the same, even though they work together. Your ABS system has its own electrical control unit which is separate from your braking system, even though the ABS and your brakes work together.

How do you reset ABS and brake light?

How to Reset an Anti-Lock Brake Light

  1. Disconnect the positive cable from the car battery, and then hold down on the brake pedal to drain the car’s electrical system. This will reset the car’s central computer. …
  2. Change the ABS sensor if the light comes back on.

What are the signs of low brake fluid?

What are the Signs of Low Brake Fluid?

  • Brake warning light has illuminated.
  • Brake fluid appears low, discolored, or dirty.
  • Brake pedal feels spongy.
  • Car takes longer to brake than normal.