Skip to content

Where is the speed sensor located on a 2010 dodge journey?

The speed sensor is located in the rear axle.

Car 2010 Dodge JourneyV6-3.5L
Service Service typeSpeed Sensor Replacement
Estimate Estimate$147.85
Shop/Dealer Price Shop/Dealer Price$171.06 – $218.20

Where is the speed control sensor located?

The vehicle speed sensor, or VSS, is located near the transmission’s output shaft. The specific placement of the sensor allows the sensor to detect, and report, to the engine’s computer through attachment cabling, the rotation and speed of the shaft.

Where is the speed sensor located on a 2009 Dodge Journey?

The speed sensor on the 2009 dodge journey is located on the right rear of the transmission near the tail shaft, under the hood of the vehicle.

What are the symptoms of a faulty speed sensor?

What Are The Symptoms Of A Faulty Speed Sensor?

  • Inconsistent Speedometer Readings. Most cars depend on signals from the wheel speed sensor to adjust their speedometer readings. …
  • The Check Engine Light Gets Activated. …
  • Malfunctioning Cruise Control. …
  • Harsh Transmission Shifting.

What is the difference between vehicle speed sensor and transmission speed sensor?

The vehicle speed sensor (VSS) is also commonly referred to as a transmission speed sensor or output shaft speed sensor. It is a small device—typically mounted somewhere on the transmission—that determines how fast your vehicle is going by measuring the rotation of a toothed wheel on a shaft inside the transmission.

Can you drive without a speed sensor?

Can you drive with a bad speed sensor? In general, it is unsafe to drive a vehicle with a broken wheel speed sensor. The car’s computer will not be able to determine the speed that your vehicle is traveling, so it might apply the brakes at a faster rate than necessary or increase the engine power.

Where is the wheel speed sensor located on a Dodge Journey?

A speed sensor is usually located on the steering knuckle behind the wheel’s brake rotor.

Can you clean ABS sensors?

With the sensor free, take your rag and wipe the sensor until it’s clean. I prefer not to use any chemicals on the sensor to avoid potential problems. If, however, the sensor is really grungy, use a mild soapy solution and rinse well. The ABS sensors are precision instruments in a crude environment.

Where is the speed sensor located on a 2012 Dodge Avenger?

The speed sensor on the 2012 Dodge Avenger is located near the front of the engine, on the transmission flange located on the lower left side. These sensors are the primary sources of information for the ABS module, essential for reduced braking systems than in conventional braking systems.

How much does a speed sensor cost?

The average cost for vehicle speed sensor replacement is between $256 and $301. Labor costs are estimated between $107 and $135 while parts are priced between $149 and $166. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

Does the speed sensor control the odometer?

1) Broken Speedometer or Odometer

Many speedometers are powered by speed sensor connected to the transmission. If this speed sensor fails, your speedometer may not work. Some odometers use the same sensor as the speedometer, and may cease to function as well.

How do you change a speed sensor?

DIY Auto Repair – Replacing a Vehicle Speed Sensor

  1. Disconnect the electrical connector and put that out of the way.
  2. Use a wrench or socket to remove the bolts. …
  3. Remove the sensor. …
  4. Coat the new VSS’ O-ring or seal with transmission fluid and reinstall.

Will a speed sensor cause shifting problems?

Without a valid speed signal from these sensors, the PCM will not be able to correctly control the shifting of gears within the transmission. This may cause the transmission to shift roughly or more quickly than normal.

What causes a wheel speed sensor to go bad?

Although sensors can go bad, the most common problem is faulty wiring or corroded electrical connections. Use an ohmmeter to test the sensor’s winding and compare it to the service specs. Typically, the readings are between 450 and 2,200 ohms. Replace any sensor that shows an open or internal short.

What happens when your wheel speed sensor goes out?

A failing wheel speed sensor will turn off your vehicle’s traction control, stability control, or any other driver assist feature. Sometimes, a damaged wire could also prevent the sensor from sending data to the control module.

Where is the rear ABS sensor located?

The ABS sensor is typically located in each wheel hub/rotor on a four channel ABS system. Some rear wheel drive applications have the sensor mounted in the rear differential.

How do I remove the ABS ring from my hub?

For drive and trailer hubs, grip the edge of the ring with locking pliers directly in front of a wheel bolt. Strike the end of the locking pliers with a mallet to lift the ring off of the hub. Work your way around the hub to remove the ring. Use emery cloth, or Scotch-Brite to clean the ABS ring diameter on the hub.