Skip to content

Where is the fuel vapor leak detection pump located on a 2014 dodge avenger?

It will be on the exterior of the vehicle, and will likely be found underneath the rear wheel well linings. Use the service manual to ensure testing procedures are followed.

Where is the fuel vapor leak detection pump?

The leak detection pump, also known as the EVAP system integrity module (ESIM), is Mopar Part No. 4861962AB for your car. The ESIM is an emissions control device and is typically mounted on the vapor canister in the rear of the car or very near to the canister.

What is a fuel vapor leak detection pump?

The leak detection pump is the component that often triggers those “Check Engine” warning lights when it detects small leaks that would be hard to see. It is required under federal law as it ensures your evaporative emission system (EVAP) is functioning correctly.

How much does it cost to replace fuel vapor leak detection?

Fuel Evaporative Canister Replacement Cost – RepairPal Estimate. The average cost for fuel evaporative canister replacement is between $405 and $453. Labor costs are estimated between $91 and $115 while parts are priced between $314 and $338.

What happens when a leak detection pump fails?

While failing a smog test is a serious enough problem, the real danger from a bad evaporative leak detection pump is the possibility that your car can be creating harmful smog due to the gas vapors escaping from the vehicle.

How do you replace a fuel vapor leak detection pump?

How to replace a leak detection pump

  1. Disconnect the negative cable from the battery.
  2. Confirm the location of the leak detection pump.
  3. Remove the pump’s vapor/vacuum lines and power connection.
  4. Install the new leak detection pump.
  5. Re-affix the pump’s vapor/vacuum lines and power connection.

How do you test a fuel vapor leak detection pump?

How to replace a leak detection pump

  1. Disconnect the negative cable from the battery.
  2. Confirm the location of the leak detection pump.
  3. Remove the pump’s vapor/vacuum lines and power connection.
  4. Install the new leak detection pump.
  5. Re-affix the pump’s vapor/vacuum lines and power connection.

Is it OK to drive with EVAP leak?

Yes, you are still safe to drive. The EVAP (Evaporated Emission Control System) is used to prevent gasoline vapors from escaping into the air from the fuel tank system to control greenhouse emissions.

How does Dodge leak detection pump work?

This system works by pumping pressurized air into the EVAP system to test it for leaks. The pump has a series of one-way valves and a vent valve, a sensor at the top, vacuum solenoid and a spring-loaded diaphragm. It uses an engine vacuum to move the diaphragm up and down.

Is EVAP leak serious?

But because an EVAP leak can potentially be a severe and environmentally damaging problem, it’s not a good idea to keep driving with the check engine light on. Whatever condition your vehicle is in—whether it’s showing symptoms of a fuel leak or not—aim to have the codes pulled as soon as possible.

Where is the EVAP canister located?

Vapor Canister Purge Valve Location

Depending on what you drive, there are two typical locations for the vapor canister purge valve. The Canister purge control valve is most often located in the engine bay on a hose going from the intake to the canister. It can also be located near the fuel tank.

What are the symptoms of an EVAP leak?

There are several common symptoms of an EVAP system leak, including:

  • Check Engine light is on.
  • Poor fuel economy.
  • Fuel System Service light is on.
  • Surging/stalling while driving.
  • Engine hesitation or misfire.
  • Low power/lack of power.
  • You smell burning carpet or fuel in the cabin.
  • Excessive smoke from the exhaust pipe.

How do I fix code P0455?

How can I fix a P0455 problem and where should I start?

  1. Check gas cap for proper tightness.
  2. Check gas cap rubber seal for cracks.
  3. Check all EVAP hoses leading to and from the charcoal canister and air cleaner assembly.
  4. Diagnose both the purge and vent control valves/solenoids.

What is code P2402?

OBD-II Code P2402 is defined as a Evaporative Emission System Leak Detection Pump Control Circuit. The Leak Detection Pump is part of the Evaporative Emissions System. After the vehicle has been sitting for a few hours, this pump will turn on and create a vacuum in the EVAP system.

What is code P0456?

Code P0456 indicates a small leak detected in the Evaporative Emissions (EVAP) system. The evaporative emissions (EVAP) system is designed to prevent fuel vapors from escaping into the atmosphere. To accomplish this, the vapors are captured and stored.

What is BMW DMTL pump?

The DMTL/LDP contains a spring loaded diaphragm which moves up and down by a solenoid that controls engine vacuum. When the DMTL/LDP is in this mode, the diaphragm produces a small amount of air pressure that is used to test for leaks. This Chrysler LDP pump is similar to the BMW DMTL.

How do I fix error code P2401?

Repairing parts to fix the P2401 engine code

  1. Replace the gas cap.
  2. Replace damaged vapor lines.
  3. Replace or repair the wiring harness.
  4. Replace the leak detection pump.
  5. Restore the purge control solenoid.
  6. Replace the ECM.

Where is the EVAP hose located?

Locate the EVAP service port adapter within the engine’s compartment. Typically, the port is near the engine’s front on the passenger side. You’ll see a valve and supply hose protruding outward.

Can a loose gas cap cause EVAP leak?

(EVAP) Leaks Are Usually Described As, A ( Large Leak ) Or ( Small Leak ): A large leak, such as that caused by a loose or missing gas cap, will set either a code P0455 ( Large Leak ) or a code P0457 ( Loose Gas Cap ).

What problems can an EVAP leak cause?

While it is safe to drive with an EVAP system leak, it causes excess car pollution. Fixing the problem is often as simple as tightening the gas cap.

What causes P0440 code?

When code P0440 is set, a leak has been detected by the Engine Control Module (ECM), or a vapor pressure sensor has malfunctioned. The ECM determines this when the vehicle is turned off, and the vent control valve is commanded closed.

How do I fix error code P2402?

What repairs can fix the P2402 code?

  1. Replace the evaporative pump and fuse.
  2. Replace the evaporative pump relay.
  3. Repair the evaporative pump connector pins for corrosion, melted, or loose connections.