Skip to content

Where is the egr valve located on a 2010 dodge charger?

All Dodge Challengers manufactured from 2008 onwards have a bolt pattern of 5 x 4.53 inches (5×115 mm).

How do you clean an EGR valve?

How to Clean EGR Valve?

  1. Spray cleaner in both openings of the EGR valve. …
  2. If it’s really dirty, you may need to use a pick to scrape off the bigger chunks of carbon or a wire brush.
  3. You may also need to let the cleaner sit in the valve for several hours.
  4. Don’t be afraid to use too much cleaner.

How do you change a EGR valve on a 2010 Dodge Journey?

How to Clean EGR Valve?

  1. Spray cleaner in both openings of the EGR valve. …
  2. If it’s really dirty, you may need to use a pick to scrape off the bigger chunks of carbon or a wire brush.
  3. You may also need to let the cleaner sit in the valve for several hours.
  4. Don’t be afraid to use too much cleaner.

Does a 2013 Dodge Charger have a EGR valve?

True. None of the 6.1L or 6.4L engines ever had an EGR valve. After 2008 none of the 5.7L engines had an EGR valve. Catch cans have nothing to do with EGR valves.

What if EGR valve is stuck closed?

If the EGR system is clogged up, or the valve is stuck closed, the combustion temperature increases. This may cause pinging (detonation), as well as surging on light acceleration. In a diesel engine, a bad EGR valve is one of the causes of a black smoke. The Check Engine light might also come on in either case.

What are the symptoms of a faulty EGR valve?

What are the symptoms of a failing EGR valve?

  • Your engine has a rough idle. …
  • Your car has poor performance. …
  • You have increased fuel consumption. …
  • Your car frequently stalls when idling. …
  • You can smell fuel. …
  • Your engine management light stays on. …
  • Your car produces more emissions. …
  • You hear knocking noises coming from the engine.

How do I unblock my EGR valve?

EGR Valve Cleaning

  1. Spray carbon deposits with EGR-valve or carburetor cleaner. …
  2. Use a dull scraper and a pipe cleaning brush to scrub carbon buildup. …
  3. To deal with rock-hard buildup, leave the valve soaking in the cleaning solution for a few minutes. …
  4. Repeat step 3 to fight stubborn carbon deposits.

Where is the EGR valve on a 2010 Dodge Journey?

The EGR valve is located in the engine compartment (underneath the hood).

Where is the EGR valve located?

The EGR valve is usually located near or attached to the intake manifold, with a tube running to the exhaust manifold. There should also be a vacuum or electrical connector (or both) running to the valve which will need to be detached.

What is an EGR valve sensor?

The EGR position sensor detects the movement and position of the exhaust gas recirculation (EGR) valve pintle. The EGR pressure sensor detects exhaust gas flow through the EGR passage.

Does 2012 Hemi have EGR valve?

There is no EGR on a 2012 5.7L. It uses variable cam timing to achieve the same thing: Drawing spent exhaust gas back into the combustion chambers to cool the combustion temps, and reduce NOX emissions under the right driving conditions.

Where is the EGR valve on a 6.1 Hemi?

Locate the EGR valve. It is in the front of the engine block, located just underneath the alternator. The top of the valve looks like a brass “flying saucer” and it is connected to the engine block with four bolts.

How do I know if my EGR valve is open or closed?

Open Position: Rough idling and problems with acceleration are the two most common indicators that the EGR valve is stuck open. The truck might also stall excessively. When the EGR valve is stuck open, all of the exhaust gas cycle back into the chamber, meaning there’s not enough oxygen for a combustion to take place.

Can you drive with a blocked EGR valve?

Can I drive with a bad EGR valve? Technically, you can drive your vehicle with a bad EGR valve, but your vehicle will run rough, shake at idle, and a check engine light will be illuminated. You might also hear popping sounds while driving down the road.

Will a bad EGR valve throw a code?

Engine code P0401 could be caused by a number of things, including a clogged EGR valve, a faulty EGR temperature sensor, or an engine vacuum leak.

How much does it cost to replace the EGR valve?

The average cost for EGR valve replacement is between $332 and $413. Labor costs are estimated between $81 and $103 while parts are priced between $251 and $311. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

Under what conditions is the EGR valve open?

The EGR valve is closed when the engine is starting up. During idle and at low speeds, only a small amount of power is required, and therefore only a small amount of oxygen, so the valve gradually opens – it can be up to 90% open at idle.

Can I replace my EGR valve myself?

In most models, replacing an exhaust gas recirculation (EGR) valve is not difficult. You can do it in your garage in about an hour or two, depending on your particular system, using some common tools and a good solvent like carburetor cleaner.

What damage can a faulty EGR valve cause?

One of the most significant parts of the EGR system is the EGR solenoid. A faulty EGR valve can damage the EGR solenoid which can, in turn, cause performance issues for the engine. The engine check light would turn on then, and then the engine might knock and ping.

How do you reset a EGR valve?

RE: EGR VALVE RESET ? to reset the CEL just unhook your NEG from the battery for about 10 mins or more and it resets when power is hooked back up…. if there is still a problem the CEL will come back on after some time.

Can the EGR valve cause starting problems?

The exhaust gas recirculation (EGR) valve introduces a measured amount of exhaust gases, into the intake manifold to get re-burned. This helps lower engine temperature and harmful emissions. But, the valve can fail and stick either open or closed. When the valve sticks open it may prevent your engine from starting.