Skip to content

How much does it cost to replace a rear drive shaft on a 2006 dodge ram 1500?

The average cost for a Dodge Ram 1500 axle shaft replacement is between $447 and $477. Labor costs are estimated between $116 and $146 while parts are priced at $331.

How much does it cost to replace a rear drive shaft?

In most cases, a new drive shaft costs somewhere between $300 and $1300. Fortunately, it only takes about an hour to replace it. A repair usually costs much less, around $200 to $300 including parts and labor, but this also depends on how many parts need to be replaced.

How long does it take to replace a driveshaft?

even a novice should have it done in about 2-3 hours taking your time and following the manual.

Is it hard to replace a driveshaft?

Replacing a driveshaft is usually a relatively straightforward affair if you have the tools and the know-how. A driveshaft is a long shaft comprised of tubes, joints, and (in some cases) a center support bearing.

Why would a drive shaft needs replacing?

If the U-joint of your drive shaft rotates too fast or fails to rotate, then it’s a problem with your drive shaft. The cap seals of the bearings could have rust on them. Either that or the u-joint itself is not stable. You’ll need to have your drive shaft replaced because you can’t drive your vehicle in this condition.

Is a broken drive shaft expensive to fix?

Usually, the Drive Shaft Repair costs will differ based on what caused the issue and how fast it can be repaired. If you just have to replace it, that would be anywhere from $500 to $1000. However, you can also expect the cost of the parts to be around half that number and the labor costs around $200.

How do I know if my drive shaft needs replacing?

Signs of a bad driveshaft/drivetrain

  1. Vibrations from under the vehicle. A common symptom of a failing driveshaft is an intense shaking coming from underneath the vehicle. …
  2. Difficulty turning. …
  3. Loud clunking noise. …
  4. Car shudders upon acceleration. …
  5. Squeaking noise. …
  6. Clicking or knocking noise.

What causes drive shaft failure?

Improper stiffness matching between the left and right smooth shafts, which results in a larger torque transmitted to the right spline, is the root cause of the drive shaft failure.

What happens if my drive shaft breaks while driving?

If your driveshaft breaks while driving, you will end up losing the traction that the drive shaft provides. You will also lose stability in your car since it can no longer rely on its wheelbase. If you are unlucky, this could mean a complete loss of control of your vehicle and possible accidents.

How much does it cost to replace a half shaft?

The average cost for CV axle replacement is between $941 and $1,070. Labor costs are estimated between $136 and $172 while parts are priced between $805 and $899. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

Do you have to replace both drive shafts?

On a high-mileage vehicle with a bad CV joint or boot, it’s often a good idea to replace both shafts at the same time. Often, the right (passenger side) shaft fails first because right turns are at a sharper angle than left turns, and right turns are more common than left turns.

How much does a drive shaft disconnect cost?

The price for a Remco drive shaft disconnect starts at $750 + installation, which requires modifying and re-balancing the existing drive shaft as part of the job.

How do you change a rear drive shaft?

The price for a Remco drive shaft disconnect starts at $750 + installation, which requires modifying and re-balancing the existing drive shaft as part of the job.

How much does it cost to get a drive shaft made?

Driveshaft Labor and Part Costs

Front driveshafts are commonly between $150 and $250, the larger rear shafts start around $250 and can reach $400 and above, possibly more for a two-piece.

How many miles will a drive shaft last?

While there is no set lifespan of a driveshaft, it typically can last about 75,000 miles. Keep in mind depending on the vehicle, and wear and tear you may get much less or much more.

Can you drive a car with a broken drive shaft?

It is not safe to drive with a bad driveshaft because the driveshaft is responsible for transferring the torque and engine rotation into vehicle movement. If your driveshaft is failing or has already failed, you won’t be able to drive your vehicle any further.

Does the drive shaft affect the transmission?

A drive shaft is a rod-like component that transmits torque from your vehicle’s engine to the wheels. It’s essentially the shaft that drives your vehicle. The driveshaft transmits torque at varying angles between driveline components.

What does a failing drive shaft sound like?

Common signs include intense car vibrations and abnormal noises, like clunking, rattling, and scraping, coming from under the vehicle.

How do you diagnose drive shaft problems?

6 Common Signs of Driveshaft Problems

  • Vibrations. An early sign of driveshaft problems is intense vibrations that come from underneath the vehicle. …
  • Squeaking Sounds. Squeaking sounds are caused by a couple of driveshaft problems. …
  • Clunking Sounds. …
  • Other Strange Noises. …
  • Movement in the U-Joint. …
  • Shuddering While Accelerating.

How do you test a rear drive shaft?

6 Common Signs of Driveshaft Problems

  • Vibrations. An early sign of driveshaft problems is intense vibrations that come from underneath the vehicle. …
  • Squeaking Sounds. Squeaking sounds are caused by a couple of driveshaft problems. …
  • Clunking Sounds. …
  • Other Strange Noises. …
  • Movement in the U-Joint. …
  • Shuddering While Accelerating.

How do you test a drive shaft?

6 Common Signs of Driveshaft Problems

  • Vibrations. An early sign of driveshaft problems is intense vibrations that come from underneath the vehicle. …
  • Squeaking Sounds. Squeaking sounds are caused by a couple of driveshaft problems. …
  • Clunking Sounds. …
  • Other Strange Noises. …
  • Movement in the U-Joint. …
  • Shuddering While Accelerating.

What happens if you don’t fix your drive shaft?

A failing driveshaft could cause clunking sounds to be heard as you step on the gas pedal or drive in reverse. These may be in addition to the squeaking sounds that you normally hear all the time. At this point, you should feel more than motivated to want to replace your shaft before some real damage occurs.

How much does an axle shaft cost?

On average, you can expect it to cost between $880 and $959 to replace your car axle shaft, depending on the type of car you drive and which axle is broken. However, it’s possible that you’ll just need to repair your axle rather than replace it.

How much is a axle shaft?

The average cost for axle shaft replacement is between $740 and $823. Labor costs are estimated between $159 and $200 while parts are priced between $581 and $623.

How much does a CV shaft cost?

CV Axle Replacement Expenses

Replacement axle shafts can be bought for between $60-150.00 each, and labor is generally between 1.5-3 hours to replace, bringing labor to around $150-350.00.

How do you service a drive shaft?

CV Axle Replacement Expenses

Replacement axle shafts can be bought for between $60-150.00 each, and labor is generally between 1.5-3 hours to replace, bringing labor to around $150-350.00.

How much does it cost to get CV joint replaced?

CV Joint Replacement Cost. A CV joint itself can cost between $95 and $210. Hiring a mechanic to perform a replacement will be between $165 and $800. The price mainly depends on whether you’re replacing a double or single axle.

How many drive shafts does a car have?

Broadly speaking, you will be able to find at least two drive shaft for your car. Depending on your car model, you can find the drive shafts next to your front wheels or rear wheels or even both (which makes it 4 drive shafts).

What is a driveshaft disconnect?

Drive Shaft Disconnect Overview

The disconnect (mechanical clutch) is installed into the rear portion of the vehicle’s drive shaft, near the rear axle. When disconnected, the rear axle is free to turn without turning the drive shaft or transmission.

Should I disconnect the drive shaft for towing?

If the drive wheels are on the ground then it may be possible to damage the transmission. If its rear wheel drive and you are towing the van forward facing (rear on the ground) you may need to disconnect the drive shaft or tow with the rear on the dolly as an alternative.

What is drive shaft coupling?

A shaft coupling is a mechanical component that connects the drive shaft and driven shaft of a motor, etc., in order to transmit power. Shaft couplings introduce mechanical flexibility, providing tolerance for shaft misalignment.

Can you install a driveshaft wrong?

The 2 piece shaft guys have a slip yoke in the middle. If they split the shaft and not re install it correctly, they will throw the shaft out of balance and cause an uncomfortable vibration.

How much is a driveshaft for a BMW?

The 2 piece shaft guys have a slip yoke in the middle. If they split the shaft and not re install it correctly, they will throw the shaft out of balance and cause an uncomfortable vibration.

How do I build a custom drive shaft?

The 2 piece shaft guys have a slip yoke in the middle. If they split the shaft and not re install it correctly, they will throw the shaft out of balance and cause an uncomfortable vibration.

What is a 1350 U joint?

Non-cross-drilled Heavy Duty 1350 U Joint

The Thrust washers in each bearing cap is to eliminate metal on metal contact preventing wear and lower overall operating temperature. It is non-greaseable design that is factory lubed with synthetic grease for excellent friction reduction.

Can a drive shaft make noise?

Another symptom of driveshaft issues is loud clunking noises. These noises are usually produced by worn-out u-joints. The ability of your driveshaft to rotate correctly is altered if your vehicle has a faulty u-joint. Lack of u-joint lubrication can cause squeaking noises when you drive at low speeds.