Skip to content

What is the code p0014 for a chevy malibu?

The code p0014 on a chevy malibu means the engine control module (ecm) has determined that the bank 1 exhaust camshaft has a problem.

How do I fix code P0014?

What repairs can fix the P0014 code?

  1. Replace camshaft timing control valve solenoid.
  2. Repair wirings to camshaft timing control valve solenoid.
  3. Clean oil lines to VCT or VVT system.
  4. Replace valve control unit (VVT or VCT, for example)
  5. Replace timing belt or timing chain.
  6. Replace camshaft position sensor.

Can you drive with a P0014 code?

While you can still drive around with P0014 registered issues, please don’t do it. Driving with it will cause hard starting, erratic idling, stalling, poor engine performance, and increased fuel consumption. Again, if a lousy VVT control solenoid triggers the issue, it may cause other related components to fail.

How much does it cost to fix a P0014 code?

While it depends on your local mechanic and their rates, it can cost anywhere between $75 and $150 per hour of labor to fix engine code P0014.

What can cause a P0014 code?

P0014 Causes

  • Engine oil is dirty.
  • Engine oil is too low.
  • Engine oil is incorrect viscosity.
  • Camshaft variable timing solenoid failure.
  • Camshaft phaser is seized in the advanced position.
  • Continuous oil flow to Variable Camshaft Timing chamber.

Will an oil change fix P0014?

In layman terms, P0014 means it’s a generic engine code that refers to an advanced or over-advanced exhaust camshaft in bank 1. Replacing your oil and filter usually fixes the P0014 OBD2 Trouble Code!

Can dirty oil cause P0014?

Can Dirty Oil Cause P0014? P0014 is caused by the position of the exhaust cam, which is why the problem can be traced back to the camshaft phaser and related components, such as the oil control solenoid and the oil viscosity. P01144 can be caused by dirty or poorly maintained motor oil.

What does engine code P1345 mean?

Toyota and Lexus specifies that fault code P1345 is indicative of a variable valve timing sensor-related issue, on the engine’s left-hand bank. Alternatively, both Audi and Volkswagen state that DTC P1345 denotes a short to ground condition, within a vehicle’s ignition amplifier circuit.

What is code P0017?

P0017 is the OBD-II generic code indicating that the crankshaft and camshaft position sensor for bank 1 exhaust camshaft do not correlate signals with each other.

Is a camshaft sensor easy to replace?

If you determine the camshaft position sensor is the problem, the good news is that replacement is usually very simple, if you can easily gain access to the sensor. The CMP sensor is mounted in several different places, depending on the model.

How much is it to replace a camshaft sensor?

Camshaft Position Sensor Replacement Cost

To replace a camshaft position sensor, you can expect to pay anywhere from $95 to $200. Parts alone will run about $25 to $100. Labor costs will be in the range of $70 to $100 for professional replacement.

How do I fix code p1345?

Loose the distributor hold down bolt with engine OFF. Make sure your OBD scanner is plugged in to monitor the Cam Retard Offset reading. Turn the engine on, let it warm to normal operating temps, and get the rpm’s above 1,000. If your reading is negative, turn the distributor counterclockwise.

How do I fix my Chevy p1345 code?

Loose the distributor hold down bolt with engine OFF. Make sure your OBD scanner is plugged in to monitor the Cam Retard Offset reading. Turn the engine on, let it warm to normal operating temps, and get the rpm’s above 1,000. If your reading is negative, turn the distributor counterclockwise.

Where is my crankshaft position sensor?

The crankshaft sensor is usually located near the bottom of the block, toward the front of the engine. In most cases, you’ll find it behind the harmonic balancer. In some vehicles, you might find the crankshaft sensor behind the timing cover, near the bottom of the block, though this is rare.

What is P0008 code?

What Does the Code P0008 Mean? P0008 is the result of a test run by the engine control module to check for misalignment between the camshafts in engine bank one and the crankshaft. The misalignment for this code would be at an idler sprocket in the bank or at the crankshaft.

What is code P0021?

What Does Code P0021 Mean? P0021 definition: Intake Camshaft Position Timing- Over-Advanced (Bank 2) Issue Severity: MODERATE– Extended driving with this code can cause internal engine damage. Repair Urgency: Get this code fixed as soon as possible.

What is code P0011?

P0011 is the OBD-II generic code indicating the engine control module (ECM) has determined that the bank 1 intake camshaft is more advanced than what the ECM has commanded it be. This over-advanced condition could be during advancing or retarding of the camshaft timing.