Skip to content

What does it mean when the abs light comes on in a chevy malibu?

The ABS relies on fluid to help regulate pressure. If the ABS fluid reservoir is low, or if there is too much air in the system, then the ABS will not be able to do its job.

How do you reset the ABS light on a Chevy Malibu?

How to Reset an Anti-Lock Brake Light

  1. Disconnect the positive cable from the car battery, and then hold down on the brake pedal to drain the car’s electrical system. This will reset the car’s central computer. …
  2. Change the ABS sensor if the light comes back on.

Can I drive my car with ABS warning light on?

It’s Safe To Drive Carefully With The ABS Light On. But Get It Looked At Quickly. You can still drive the car with your ABS light on, because it does not impact normal braking. However, we wouldn’t recommend you do this because your ABS system helps to control stopping, and it can be dangerous to be driving without it.

How much does it cost to fix ABS on Chevy Malibu?

The Best in Auto Repair

The average cost for a Chevrolet Malibu ABS control module replacement is between $601 and $645. Labor costs are estimated between $168 and $212 while parts are priced at $433.

What causes your ABS light to come on?

The four common reasons that typically cause this light to turn on include a malfunctioning ABS module, low levels in the fluid reservoir, broken wheel speed sensors, or the system is turned off. Your ABS actually shares some important components with another system in your vehicle: your traction control system.

Should I be worried if my ABS light is on?

When your car’s ABS light comes on, it means there is a problem with your vehicle’s braking system. You need to address this issue, otherwise, it could make your car unsafe to drive. ABS is a type of braking system used in all cars produced since Sept. 1, 2011.

What causes ABS to fail?

The most common ABS problems occur when sensors become contaminated with debris or metal shavings. Malfunctions also occur when sensor wiring becomes damaged, resulting in intermittent or no continuity.

How much does ABS cost to fix?

An ABS control module replacement can range from $320 to over $1,000. The wide price range isn’t really driven by labor cost, which will typically be around $80-$120. It depends on how much the control module costs and how difficult it is to source.

How much does it cost to fix an ABS sensor?

The average ABS wheel speed sensor replacement cost is between $200 and $400 per sensor, depending on the car model and labor costs. You can expect to pay about $100 to $150 for the wheel speed sensor and another $100 to $300 for the labor.

How do I get the ABS light to turn off?

Locate the DIC control panel on the dashboard in front of the driver’s seat under the speedometer. Keep pushing and releasing the “Set” button on the DIC control panel until “ABS” is shown. Hold the “Set” button for about 5 seconds to reset the light and turn it off.

How do you reset the ABS light on a 2014 Chevy Malibu?

Locate the DIC control panel on the dashboard in front of the driver’s seat under the speedometer. Keep pushing and releasing the “Set” button on the DIC control panel until “ABS” is shown. Hold the “Set” button for about 5 seconds to reset the light and turn it off.

Can worn brake pads cause ABS light to come on?

So you might ask, Can worn brake pads cause ABS light to come on? No! This light illuminates in the dashboard where there is a brake-related problem. Your brake pads are not identified as part of the ABS, the ABS light will not come on when they are worn.

Can blown fuse cause ABS light to come on?

Sometimes a blown fuse to the ABS can cause the light to come on and stay on. Fuses are easy to blow, so sometimes it’s an easy fix to check.

Can bad tires cause ABS light to come on?

When the ABS and Traction Control lights illuminate, it is typically due to a faulty wheel or speed sensor or an ABS module failure.

What does ABS light indicate?

CARS.COM — ABS stands for antilock braking system, and if the ABS warning light is illuminated in your car’s gauge cluster, that means the antilock system has been deactivated because of a malfunction.

How do you fix ABS problems?

Methods of Troubleshooting ABS brakes

  1. Put the key in the ignition and turn the car on and off, if the ABS light appears on the dashboard. …
  2. Clean the front wheel sensors if your ABS pulses at low speed while little pressure is applied. …
  3. Apply pressure to the ABS brake if it won’t stop.

How do you tell if ABS pump is bad?

So, when an ABS control module fails, you’ll likely notice it when you’re braking heavily. A bad ABS module can behave erratically, making your brakes lock up even under normal braking. You might even notice unusual behavior from the brakes, like random clicking noises. These can also indicate ABS module failure.

Does ABS damage your car?

UNNECESSARILY TRIGGERS ABS

Hard braking can damage your car as well by triggering its ABS, or anti-lock braking system. Modern cars utilize this feature to keep their tires from fully stopping—even when you completely slam on the brakes.

Can you drive without ABS sensor?

In the winter, braking on any slippery surface will be as if the vehicle isn’t equipped with ABS at all: Locked wheels, no steering, and decreased control. But, the brakes still have all the functionality they were equipped with from the factory, just no electronic ability to help the driver in a bad situation.