Skip to content

How much is a mass air flow sensor for a bmw 325i?

BMW 325i Mass Airflow Sensor Replacement Cost Estimate. The average cost for a BMW 325i mass airflow sensor replacement is between $434 and $636. Labor costs are estimated between $26 and $33 while parts are priced between $408 and $603.

How much is a BMW mass air flow sensor?

The average cost for a BMW 328i mass airflow sensor replacement is between $452 and $570. Labor costs are estimated between $51 and $64 while parts are priced between $401 and $506.

What are the symptoms of a failed mass air flow sensor?

Bad Mass Air Flow Sensor Symptoms

  • Check Engine Light On. A bad MAF sensor can lead to illuminated check engine light, one of the warning lights on car dashboard. …
  • Acceleration Trouble. …
  • Rough Idling. …
  • Poor Fuel Efficiency. …
  • Dark Exhaust Smoke. …
  • Surging or Hesitation. …
  • Hard Starting.

What problems can a mass air flow sensor cause?

Mass Air flow Sensor (MAF). As a result, a bad mass air flow sensor causes various driveability problems, including a no-start, stalling, lack of power and poor acceleration. In addition, a faulty mass air flow sensor might cause the Check Engine or Service Engine Soon light to come on.

How serious is a mass air flow sensor?

A bad MAF sensor can cause your vehicle to experience poor drivability issues such as engine stalling, jerking or hesitation during acceleration. This could happen while speeding up on the highway on-ramp or cruising down a city street. These issues can create dangerous situations causing accidents and injury.

How long does it take to replace a mass air flow sensor?

Less than one hour. Disconnect the negative battery terminal. Unplug the electrical connector on the mass air flow sensor.

Can a mass air flow sensor cause transmission problems?

The Mass Airflow Sensor measures airflow into the engine intake assembly and is used to determine engine load. If it fails it can cause automatic transmission problems such as late harsh shifts, early soft shifts, or can result in no shifting at all.

How do I know if my MAF sensor is dirty?

Six Signs My Car’s Mass Airflow Sensor (MAF) Is Bad

  1. Lean or Rich Fuel Mixture. …
  2. Difficulty Starting Your Car. …
  3. Engine Stalls After Starting or When Idling. …
  4. Engine Hesitation and Dragging. …
  5. Engine Hesitation and Jerking. …
  6. Engine Hiccups.

How do I reset my mass airflow sensor?

Upon replacing the Mass Air Flow Sensor, turn on the engine light to ensure it still has its function. You can unhook the battery and leave it unhooked for 10 minutes to completely reset the entire system. The battery will not harm itself if left unhooked for more than 10 minutes.

How do you fix a mass air flow sensor?

How to Fix a Bad Mass Air Flow Sensor

  1. Shake out the dust. Blow out the intake tubing and install a new air filter to prevent future dust intrusion.
  2. Use a cleaner. An MAF-sensor-specific cleaner may be able to take care of any contamination.
  3. Replace it.

Can you drive without a mass air flow sensor?

The result of driving without plugging the MAF sensor can lead to permanent damage to your engine computer and/or oxygen sensor. If you decide to drive with the MAF sensor unplugged, the side effects of doing so include poor gas mileage and power.

Can a mass air flow sensor be cleaned?

Cleaning the MAF as part of regular routine maintenance can help reduce and/or prevent these problems. If the MAF sensor is at fault, cleaning it can help, and many times, even solve the problem. This can be done at home. You just need to remove the component, clean it, and reattach it to your engine air intake system.

Is it better to clean or replace a mass air flow sensor?

Generally, you’ll want to clean your mass airflow sensor either every six months, or every time you change your oil. Cleaning it when you change or clean your air filter will be a good way to save both time and money.

How do you check a mass air flow sensor?

Pop the hood open. Lightly tap the MAF sensor and electrical connector with a screwdriver handle. Wiggle the wires as well. If the engine stalls, idle is upset, or idle gets better, the MAF sensor is likely defective.

How hard is it to replace a mass air flow sensor?

Pop the hood open. Lightly tap the MAF sensor and electrical connector with a screwdriver handle. Wiggle the wires as well. If the engine stalls, idle is upset, or idle gets better, the MAF sensor is likely defective.

Will a dirty mass air flow sensor throw a code?

As was mentioned, air/fuel ratio and misfire codes may also point to a problem with the MAF sensor (though, there are many other possibilities, as well). Keep in mind: Sometimes, a bad MAF sensor won’t set a code, especially on older vehicles with a type of self-diagnostics called OBD-1.

Can a dirty throttle body cause shifting problems?

The throttle position sensor is used to control the amount of gas that goes into the engine and thereby determine engine load and control vehicle speed. If it fails, it can result in automatic transmission hard-shifting issues.

How many sensors are on a transmission?

Typically, two sensors communicate the transmission data to the vehicle’s powertrain control module. The first sensor, referred to as the input sensor, monitors the speed of the transmission’s input shaft. The second sensor is the output sensor, which monitors the output shaft speed.

Why does my car run better with MAF unplugged?

If the car is running better with the MAF sensor unplugged, it means that the sensor is sending inaccurate readings and needs to be either cleaned or replaced.

Where is the mass airflow sensor located?

The mass air flow sensor (MAF) is a key component of the electronic fuel injection system in a car. It is located between the air filter and the engine’s intake manifold.

Can a dirty mass air flow sensor cause misfire?

Even a dirty MAF sensor can cause a lean code and/or misfire to occur. The engine may be stalling because it isn’t getting enough throttle opening.

Does MAF affect fuel pressure?

Signs of a bad MAF sensor may mimic problems such as low vacuum, low compression, or low fuel pressure due to a bad fuel pump. The most common symptoms of a malfunctioning MAS sensor include: The engine is hard to start or has trouble turning over. The engine stalls soon after starting.

What does a mass airflow sensor do in a car?

A device in the throttle body, the mass airflow, or MAF, sensor helps the engine computer determine the proper air-fuel mixture by measuring the mass of the air flowing past it.

How many miles should a mass air flow sensor last?

The life of your MAF sensor can be extended with regular maintenance and air filter replacement. A good rule of thumb is to drive every 10,000 to 12,000 miles. Mass airflow sensors (MAF) have no expiration date.

Can I use wd40 to clean MAF sensor?

DO NOT USE WD-40. Use a cleaner that is meant for electrical parts. Brake cleaner is essentially the same stuff. I’ve also used something called ‘thottle body cleaner’ whose label indicated it was safe for cleaning MAF’s.

How do you clean a BMW MAF?

DO NOT USE WD-40. Use a cleaner that is meant for electrical parts. Brake cleaner is essentially the same stuff. I’ve also used something called ‘thottle body cleaner’ whose label indicated it was safe for cleaning MAF’s.